Ciao,
esce da breve il nuovo XM/XW Airmax 5.6.3.
Ecco le release notes:
AirOS V Firmware Revision History
====================================================================
Supported products
* Bullet M2/M5/Titanium
* Rocket M2/M2 Titanium/M3/M365/M900/M5/M5 GPS/M5 Titanium/M6
* NanoStation M2/M3/M365/M5/M6
* NanoStation Loco M2/M900/M5
* NanoBridge M2/M3/M365/M900/M5
* AirGrid M2/M5/HP/HP New
* PowerBridge M3/M365/M5/M10
* LiteBeam M5
* PicoStation M2
* AirRouter/HP
* PowerAP N
====================================================================
Version 5.6.3-Service release (November 30, 2015)
------------------------------------------------
Regulatory updates:
- New: Enable UNII2 band after Revised UNII Rules activation for certified models (United States/Puerto Rico)
- New: Revised UNII Rules activation for certified models:
Rocket M5
NanoBridge M5
PowerBeamM5 300/400/620
NanoBeam M5 16/19
- Fix: Revised UK/DFS rules
- Fix: Disabled UNII2 frequencies for AP-Repeater after Revised UNII Rules gets activated (FCC regulatory restrictions)
- Fix: Limit channel width to 20MHz for Indonesia
- Fix: Reduce EIRP for Pakistant to 20dBm/100mW (5GHz)
Improvements:
- New: Linux kernel upgrade to 2.6.32.68 (possible fix for random AP reboots)
- New: DHCP server IP range is suggested according LAN IP address/netmask values
- New: Antenna model selection in Wireless page
- New: Allow to disable remote statistics reporting via Extra Reporting option in Advanced configuration page
- New: Default password change request before applying configuration changes
Fixes:
- airMAX: Security improvements
- Fix: Generate SSL certificate start date from firmware build timestamp
- Fix: Network settings are not fully loaded in case if bridge section is missing in configuration file
- Fix: AP crash prevention in power save mode
- Fix: Incorrect antenna selection for Rocket M900
- Fix: DFS AP doesn't change channel after NOL timeout
- Fix: Don't require to change default password if configuration backup was uploaded with updated credentials
- Fix: Egress traffic is limited on VLAN interfaces when rules are set on parent
- Fix: Simplified airView tool launch
- Fix: Enable airView for LiteBeam M5 23
- Fix: Optimise remote statistics collection to reduce infctld CPU usage
- Fix: Improve frequency scan for XW series radios
- Fix: PHP2 buffer overflow
- Fix: Station doesn't connect back to AP after it was kicked or AP was rebooted
- Fix: Reduce remote statistics bursts from AP and randomise transmit interval
- Fix: Remove Station only and airMAX only restriction for LiteBeam M5 23 product
- Fix: Improve AC2 agent response to server after device reboot
- Fix: Wrong frequency list after session timeout
- Fix: Respond on wireless interface for discovery requests when PPPoE client is configured
- Fix: Validate overlapping 30MHz width channels
- Fix: Enabling "Hide Indoor Channels" cause station to lockup
- Fix: wpa_supplicant no timestamp check
- WEB UI: Translations update
- WEB UI: Device Name displaying incorrectly when using symbol &
- WEB UI: Show possible LAN negotiation speed for gigabit capable devices
- WEB UI: TX Power reporting in MAIN page when set 0dBm
- WEB UI: Show antenna gain input field for devices which have single antenna option and no built-in antenna
- WEB UI: Show correct antenna in main tab if there are two antennas with same gain value
- WEB UI: Move Refresh button to top of the Stations list
- WEB UI: Hide TX signal in Station list if remote statistics are disabled
- WEB UI: TX power slide doesn't allow dragging
A breve lo metterò in test pre produzione e vi aggiorno con i miei feedback. Per ora su una pico m2 si osservano cambiamenti in wireless ( antenna FCC / EU obbligata ) --> questo vuol dire BASTA antenne di terze parti sulla PICO ( ed era ora .... ) e in advanced ( velocità lan AUTO specificata come AUTO 10/100 ... / 1000 dove giga ).
Ciao
TheMa3x
