Problemino con Rocket M5 gps

[thema3x]

mmm...

mi sembra strana la cosa: purtroppo non posso entare nello specifico, in quanto tutte le ns. infrastrutture ( formate ad oggi da circa 30 antenne, sparse su un raggio di 5 Km ) sono composte da nanostation e powerbridge M5...il difetto del reboot xò è strano:

IDEA:

--> services ( tendina ) => attiva il log e fallo scaricare su un syslog esterno, cosi vediamo dai log perchè si raivvia il sistema: poi si riavvia l' o.s. o proprio l hw ?

La differenza sta che se si riavvia solo l' os il power led sta acceso e si spegne solo per alcuni secondi il lan led; se si ravvia l' hw il led power si spegene e poi si raiccende, idem il lan, e per un attimo tutti i led del signal si accendono.

Dobbiamo risolvere il tuo problema . . .

Ciao

Thema3x

[stormy]

Hai mica fatto una prova senza WDS ??????
giusto per semplificare ancor di più il tutto....

_______________________________
Stormy

[marco dsng]

Scusate ma non avevo letto le ultime risposte che mi avete dato non avevo visto la pagina 2.
Dopo altri test ho verificato che probabilmente era il roket in questione difettoso, si sganciava senza traffico, o altrimenti in fase di aggancio con la seconda cpe, a un certo punto addirittura entrando nella web interface, ho resettato, reinstallato il firmware, ma non cambiava nulla, alimentato a 10 cm con 24 volt e impostando la potenza a 0dbm niente da fare.
Ho preso una nanobridge per fargli fare lo stesso lavoro e non ha fatto mai una piega, con gli airgrid anche.
Sarà probabilmente una saldatura fredda o qualche difetto hardware della scheda, ho notato sul forum ufficiale che qualche altro ha riscontrato problemini di questo tipo.
comunque allego alcuni log del rocket e delle cpe collegate, come potete riscontrare dopo un tot non vedono il segnale poi si riagganciano.
Nella versione precedente di firmware ad ogni reboot si cancellava il log, con la nuova è molto più veloce e a volte lo mantiene.

un log della rocket

non guardate i txrx rate, ero in laboratorio ed erano fissati cosi per test.


tatus
Device Name:Master
Network Mode:Bridge
Wireless Mode:Access Point WDS
SSID:ubnt
Security:none
Version:v5.4.5.
Uptime:00:14:38
Date:2012-03-20 00:14:34
Channel/Frequency:140 / 5700 MHz
Channel Width:20 MHz
ACK/Distance:24 / 0.1 miles (0.2 km)
TX/RX Chains:2X2
WLAN MAC:00:27:22:2A:8C:A8
LAN MAC:00:27:22:2B:8C:A8
LAN1/LAN2:Unplugged / Unplugged
AP MAC:00:27:22:2A:8C:A8
Connections: 3
Noise Floor:-91 dBm
Transmit CCQ:100 %
AirMax:Disabled
GPS Signal Quality:

0 %
Latitude / Longitude:- / -
Altitude:-

Monitor
Throughput | Stations | ARP Table | Bridge Table | Routes | GPS Details | Log

System Log
Mar 20 00:00:17 Master syslog.info syslogd started: BusyBox v1.11.2
Mar 20 00:00:18 Master user.notice system: Start
Mar 20 00:00:18 Master daemon.info init: starting pid 2492, tty '/dev/null': '/bin/infctld -m -c'
Mar 20 00:00:18 Master daemon.info init: starting pid 2493, tty '/dev/null': '/bin/syslogd -n -S'
Mar 20 00:00:18 syslogd started: BusyBox v1.11.2
Mar 20 00:00:18 init: starting pid 2494, tty '/dev/null': '/usr/bin/iwevent -s'
Mar 20 00:00:18 init: starting pid 2495, tty '/dev/null': '/bin/lighttpd -D -f /etc/lighttpd.conf'
Mar 20 00:00:18 init: starting pid 2496, tty '/dev/null': '/bin/dropbear -F -d /etc/persistent/dropbear_dss_host_key -r /etc/persistent/dropbear_rs
Mar 20 00:00:18 init: starting pid 2497, tty '/dev/null': '/usr/bin/ubnt-gps-reader -i /dev/ttyS0 -o /proc/sys/dev/ubnt_poll/gps_info -s 9600 -j /t
Mar 20 00:00:18 dropbear[2496]: Not backgrounding
Mar 20 00:01:16 wireless: ath0 Registered node:00:27:22:A8:03:97
Mar 20 00:01:16 wireless: ath0 Registered node:00:27:22:A8:05:3F
Mar 20 00:01:16 wireless: ath0 Registered node:00:27:22:64:55:19
Mar 20 00:06:00 init: reloading /etc/inittab
Mar 20 00:06:00 system: Stop
Mar 20 00:06:01 dropbear[2496]: premature exit: Terminated by signal
Mar 20 00:06:01 wireless: ath0 Sending disassoc to 00:27:22:a8:03:97. Reason: Station has left the basic service area and is disassociated (8).
Mar 20 00:06:01 wireless: ath0 Expired node:00:27:22:A8:03:97
Mar 20 00:06:01 wireless: ath0 Sending disassoc to 00:27:22:a8:05:3f. Reason: Station has left the basic service area and is disassociated (8).
Mar 20 00:06:01 wireless: ath0 Expired node:00:27:22:A8:05:3F
Mar 20 00:06:01 wireless: ath0 Sending disassoc to 00:27:22:64:55:19. Reason: Station has left the basic service area and is disassociated (8).
Mar 20 00:06:01 wireless: ath0 Expired node:00:27:22:64:55:19
Mar 20 00:06:01 init: process '/bin/lighttpd -D -f /etc/lighttpd.conf' (pid 2495) exited. Scheduling for restart.
Mar 20 00:06:01 init: process '/bin/dropbear -F -d /etc/persistent/dropbear_dss_host_key -r /etc/persistent/dropbear_rsa_host_key -p 22 ' (pid 2496
Mar 20 00:06:02 wireless: ath0 Set Encryption key:off
Mar 20 00:06:02 Master syslog.info syslogd exiting
Mar 20 00:06:02 syslogd exiting
Mar 20 00:06:13 Master syslog.info syslogd started: BusyBox v1.11.2
Mar 20 00:06:13 Master user.notice system: Start
Mar 20 00:06:13 Master daemon.info init: reloading /etc/inittab
Mar 20 00:06:13 Master daemon.info init: starting pid 3222, tty '/dev/null': '/bin/infctld -m -c'
Mar 20 00:06:13 Master daemon.info init: starting pid 3223, tty '/dev/null': '/bin/syslogd -n -S'
Mar 20 00:06:13 syslogd started: BusyBox v1.11.2
Mar 20 00:06:13 init: starting pid 3224, tty '/dev/null': '/usr/bin/iwevent -s'
Mar 20 00:06:13 init: starting pid 3225, tty '/dev/null': '/bin/lighttpd -D -f /etc/lighttpd.conf'
Mar 20 00:06:13 init: starting pid 3226, tty '/dev/null': '/bin/dropbear -F -d /etc/persistent/dropbear_dss_host_key -r /etc/persistent/dropbear_rs
Mar 20 00:06:13 init: starting pid 3227, tty '/dev/null': '/usr/bin/ubnt-gps-reader -i /dev/ttyS0 -o /proc/sys/dev/ubnt_poll/gps_info -s 9600 -j /t
Mar 20 00:06:13 dropbear[3226]: Not backgrounding
Mar 20 00:07:14 wireless: ath0 Registered node:00:27:22:A8:05:3F
Mar 20 00:07:14 wireless: ath0 Registered node:00:27:22:A8:03:97
Mar 20 00:07:17 wireless: ath0 Registered node:00:27:22:64:55:19
System Log
Dec 19 20:40:15 UBNT syslog.info syslogd started: BusyBox v1.11.2
Dec 19 20:40:15 UBNT user.notice system: Start
Dec 19 20:40:15 UBNT daemon.info init: starting pid 2386, tty '/dev/null': '/bin/infctld -m -c'
Dec 19 20:40:15 UBNT daemon.info init: starting pid 2387, tty '/dev/null': '/bin/syslogd -n -S'
Dec 19 20:40:16 UBNT daemon.info init: starting pid 2391, tty '/dev/null': '/usr/bin/ubnt-gps-reader -i /dev/ttyS0 -o /proc/sys/dev/ubnt_poll/gps_info -s 9600 -j /t
Dec 19 20:40:16 UBNT daemon.info init: starting pid 2389, tty '/dev/null': '/bin/lighttpd -D -f /etc/lighttpd.conf'
Dec 19 20:40:16 UBNT daemon.info init: starting pid 2390, tty '/dev/null': '/bin/dropbear -F -d /etc/persistent/dropbear_dss_host_key -r /etc/persistent/dropbear_rs
Dec 19 20:40:16 UBNT authpriv.info dropbear[2390]: Not backgrounding
Dec 19 20:40:16 syslogd started: BusyBox v1.11.2
Dec 19 20:40:16 init: starting pid 2388, tty '/dev/null': '/usr/bin/iwevent -s'
Dec 19 20:40:16 usb-modeswitch: 1-0:1.0: Manufacturer=Linux_2.6.15-5.2_ehci_hcd Product=ATH_EHCI Serial=ar7240-ehci.0
Dec 19 20:40:17 usb-3g: 1-0:1.0: 0000:0000 Manufacturer=Linux_2.6.15-5.2_ehci_hcd Product=ATH_EHCI Serial=ar7240-ehci.0



un'altro
System Log
Dec 19 20:40:15 UBNT syslog.info syslogd started: BusyBox v1.11.2
Dec 19 20:40:15 UBNT user.notice system: Start
Dec 19 20:40:15 UBNT daemon.info init: starting pid 2386, tty '/dev/null': '/bin/infctld -m -c'
Dec 19 20:40:15 UBNT daemon.info init: starting pid 2387, tty '/dev/null': '/bin/syslogd -n -S'
Dec 19 20:40:16 UBNT daemon.info init: starting pid 2391, tty '/dev/null': '/usr/bin/ubnt-gps-reader -i /dev/ttyS0 -o /proc/sys/dev/ubnt_poll/gps_info -s 9600 -j /t
Dec 19 20:40:16 UBNT daemon.info init: starting pid 2389, tty '/dev/null': '/bin/lighttpd -D -f /etc/lighttpd.conf'
Dec 19 20:40:16 UBNT daemon.info init: starting pid 2390, tty '/dev/null': '/bin/dropbear -F -d /etc/persistent/dropbear_dss_host_key -r /etc/persistent/dropbear_rs
Dec 19 20:40:16 UBNT authpriv.info dropbear[2390]: Not backgrounding
Dec 19 20:40:16 syslogd started: BusyBox v1.11.2
Dec 19 20:40:16 init: starting pid 2388, tty '/dev/null': '/usr/bin/iwevent -s'
Dec 19 20:40:16 usb-modeswitch: 1-0:1.0: Manufacturer=Linux_2.6.15-5.2_ehci_hcd Product=ATH_EHCI Serial=ar7240-ehci.0
Dec 19 20:40:17 usb-3g: 1-0:1.0: 0000:0000 Manufacturer=Linux_2.6.15-5.2_ehci_hcd Product=ATH_EHCI Serial=ar7240-ehci.0

adesso quelli delle cpe


Status
Device Name:TX1
Network Mode:Bridge
Wireless Mode:Station WDS
SSID:ubnt
Security:none
Version:v5.3.5.
Uptime:02:47:29
Date:2012-03-14 02:47:26
Channel/Frequency:140 / 5700 MHz
Channel Width:20 MHz
ACK/Distance:28 / 0.1 miles (0.2 km)
TX/RX Chains:1X1
Antenna:Not specified
WLAN MAC:00:27:22:A8:03:97
LAN MAC:00:27:22:A9:03:97
LAN:Unplugged
AP MAC:00:27:22:2A:8C:A8
Signal Strength:

-67 dBm
Noise Floor:-91 dBm
Transmit CCQ:99.1 %
TX/RX Rate:65.0 Mbps / 6.5 Mbps
AirMax:-

Monitor
Throughput | AP Information | ARP Table | Bridge Table | Routes | Log

System Log
Mar 14 00:02:07 ubnt: Messages cleared.
Mar 14 00:07:58 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 00:08:03 wireless: ath0 Scan request completed
Mar 14 00:09:23 wireless: ath0 Scan request completed
Mar 14 00:09:23 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:08:02 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:08:07 wireless: ath0 Scan request completed
Mar 14 01:09:27 wireless: ath0 Scan request completed
Mar 14 01:09:27 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:19:44 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:19:50 wireless: ath0 Scan request completed
Mar 14 01:21:10 wireless: ath0 Scan request completed
Mar 14 01:21:10 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:23:33 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:23:38 wireless: ath0 Scan request completed
Mar 14 01:24:59 wireless: ath0 Scan request completed
Mar 14 01:24:59 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:38:49 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:38:54 wireless: ath0 Scan request completed
Mar 14 01:40:14 wireless: ath0 Scan request completed
Mar 14 01:40:14 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:55:01 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:55:06 wireless: ath0 Scan request completed
Mar 14 01:56:26 wireless: ath0 Scan request completed
Mar 14 01:56:26 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 02:23:48 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 02:23:53 wireless: ath0 Scan request completed
Mar 14 02:25:13 wireless: ath0 Scan request completed
Mar 14 02:25:13 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 02:28:57 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 02:29:02 wireless: ath0 Scan request completed
Mar 14 02:30:22 wireless: ath0 Scan request completed
Mar 14 02:30:22 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 02:35:08 wireless: ath0 Received disassoc from 00:27:22:2a:8c:a8. Reason: Station has left the basic service area and is disassociated (8).
Mar 14 02:35:08 wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 02:36:20 wireless: ath0 Scan request completed
Mar 14 02:36:20 wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8


un'altro


tatus
Device Name:TX2
Network Mode:Bridge
Wireless Mode:Station WDS
SSID:ubnt
Security:none
Version:v5.3.5.
Uptime:02:52:38
Date:2012-03-14 02:52:35
Channel/Frequency:140 / 5700 MHz
Channel Width:20 MHz
ACK/Distance:28 / 0.1 miles (0.2 km)
TX/RX Chains:1X1
Antenna:Not specified
WLAN MAC:00:27:22:A8:05:3F
LAN MAC:00:27:22:A9:05:3F
LAN:100Mbps-Full
AP MAC:00:27:22:2A:8C:A8
Signal Strength:

-76 dBm
Noise Floor:-91 dBm
Transmit CCQ:98.5 %
TX/RX Rate:65.0 Mbps / 6.5 Mbps
AirMax:-

Monitor
Throughput | AP Information | ARP Table | Bridge Table | Routes | Log

System Log
Mar 14 00:06:57 ubnt: Messages cleared.
Mar 14 00:12:04 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 00:12:09 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 00:13:29 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 00:13:29 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:12:08 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:12:13 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 01:13:33 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 01:13:33 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:23:51 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:23:56 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 01:25:16 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 01:25:16 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:27:39 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:27:44 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 01:29:05 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 01:29:05 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:42:55 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:43:00 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 01:44:20 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 01:44:20 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 01:59:07 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 01:59:12 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 02:00:32 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 02:00:32 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 02:27:54 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 02:27:59 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 02:29:20 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 02:29:20 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 02:33:03 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 02:33:08 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 02:34:28 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 02:34:28 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8
Mar 14 02:39:14 TX2 daemon.info wireless: ath0 Received disassoc from 00:27:22:2a:8c:a8. Reason: Station has left the basic service area and is disassociated (8).
Mar 14 02:39:14 TX2 daemon.info wireless: ath0 New Access Point/Cell address:Not-Associated
Mar 14 02:40:26 TX2 daemon.info wireless: ath0 Scan request completed
Mar 14 02:40:26 TX2 daemon.info wireless: ath0 New Access Point/Cell address:00:27:22:2A:8C:A8


Sinceramente non lo so leggere, ma utilizzando la nano e airgrid come AP stanno in piedi per il tutto non fa una piega.

Questo è un difetto hardware che nell'utilizzo normale tipo navigazione internet non te ne rendi conto. Sopratutto con l'ultimo firm perchè è molto veloce nel reboot.

auguri di buona pasqua a tutti!

[thema3x]

Ottimo !

Il log se lo guardi con attenzione dopo un po impari a leggero, ma nel tuo caso non importa.

Abbiamo capito il problema, a volte può seccedere: a me su due nano M2 nuove appena attivato il poe passtrough tra le porte ( porta 2 nc. quindi senza carico ) la prima è scoppiata, le seconda si è bruciata la parte lan . . .fai te !

in questi casi . . .RMA

Ciao

TheMa3x

[marco dsng]

Ok, ma i problemi c'erano prima comunque. non ho notato nessun cambiamento.

Verso la fine delle verifiche, volendo essere certo che non ci fossero cadute di tensione (occulte) in alimentazione da rj45 1 rocket all'interno, ho provato a aprire il passaggio di tensione alla porta 2 e alimentare anche dall'altra parte
; 24 v in parallelo -comunque non carico la circuiteria interna esco a 0dbm.
se da una parte interna sul rj45 ho porcherie che mi generano cadute compenso con l'altra.
Esplosioni non ne ho sentite.

Ovvio prova empirica, non posso aprire l'aggeggio provo anche questa.
Comunque il comportamento non è cambiato.
non sò ma le altre funzionano regolari, in elettronica o si guastano subito o vanno per sempre, più o meno...


Riepilogando:

il problema è comparso nell'immediato: reboot random

chiedo all'assistenza aiuto e mi viene risposto: "calo di tensione sull'alimentazione" diagnosi telefonica perfetta.

alimento a 10 cm va un tot poi reboot random

Assemblo altro poe controllo tensioni ma non cambia nulla, reboot random

Cambio firmware: reboot più svelto....random

Visita al santuario della Madonna della Stella: reboot....

Visita dal mago Genny ( di onestà garantite dalle IENE in diretta): reboot....

Extrema ratio: RMA


Attendo ora
devoto,
con terrore,
ansia e trepidazione ,

da colui che decide.... sulla via Appia,

la soluzione finale.

[thema3x]

Ciao,

quoto EXTREMA RATIO

[nventawires]

Hello, La via Appia Dixit:
intanto te ne mandiamo uno nuovo di pacca in sostituzione.. poi con calma facciamo le verifiche su questo che ci hai mandato.. perchè il caso è particolare..... ed in questi giorni il laboratorio è incasinatissimo per altre cose... poi ti facciamo sapere con precisione.. o altrimenti lo mandiamo alla casa MAMMA...

A presto,
NVENTA

[marco dsng]

Grazie! ottimo!

[thema3x]

Ottimo !!

..io ne ho 3 in coda che aspettano...anche loro per problemi "particolari " ( vedi post specifico falut NSM2 )

Santo il Laboratorio sia direi

[marco dsng]

Sostituito rocket,
perfetto.